Last Modified: 11-29-2007 1.6 U
Service Category: Vehicle Exterior Section: Window/Glass
Model Year: 2008 Model: Sequoia Doc ID: RM0000027QL00GX
Title: WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: DATA LIST / ACTIVE TEST (2008 Sequoia)

DATA LIST / ACTIVE TEST

1. READ DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Warm up the engine.

(b) Turn the ignition switch off.

(c) Connect the Techstream to the DLC3.

(d) Turn the ignition switch to ON.

(e) Turn the Techstream on.

(f) Enter the following menus: Body Electrical / (desired system) / Data List.

(g) According to the display on the Techstream, read the Data List.

Master Switch

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

D Door P/W Auto SW

Driver side power window auto UP/DOWN switch signal / ON or OFF

ON: Driver side power window auto UP/DOWN switch on power window regulator master switch operated

OFF: Driver side power window switch on power window regulator master switch not operated

-

P Door P/W Auto SW

Front passenger side power window remote auto UP/DOWN switch signal / ON or OFF

ON: Front passenger side power window remote auto UP/DOWN switch on power window regulator master switch operated

OFF: Front passenger side power window switch on power window regulator master switch not operated

-

P Door P/W Up SW

Front passenger side power window remote manual UP switch signal / ON or OFF

ON: Front passenger side power window remote manual UP switch on power window regulator master switch operated

OFF: Front passenger side power window switch on power window regulator master switch not operated

-

P Door P/W Down SW

Front passenger side power window remote manual DOWN switch signal / ON or OFF

ON: Front passenger side power window remote manual DOWN switch on power window regulator master switch operated

OFF: Front passenger side power window switch on power window regulator master switch not operated

-

Window Lock Switch Status

Power window LOCK switch / ON or OFF

ON: The Power window lock switch LOCK position

OFF: The Power window lock switch UNLOCK position

-

Number of Trouble Codes

Number of trouble codes / Min.: 0, Max.: 255

Number of DTCs will be displayed

-

D-Door Motor

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

D Door P/W Auto SW

Driver side power window auto UP/DOWN switch signal / ON or OFF

ON: Driver side power window auto UP/DOWN switch operated

OFF: Driver side power window switch not operated

-

D Door P/W Up SW

Driver side power window MANUAL UP switch signal / ON or OFF

ON: Driver side power window manual UP switch operated

OFF: Driver side power window switch not operated

-

D Door P/W Down SW

Driver side power window MANUAL DOWN switch signal / ON or OFF

ON: Driver side power window manual DOWN switch operated

OFF: Driver side power window switch not operated

-

Number of Trouble Codes

Number of trouble codes / Min.: 0, Max.: 255

Number of DTCs will be displayed

-

P-Door Motor

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

P Door P/W Auto SW

Front passenger side power window auto UP/DOWN switch signal / ON or OFF

ON: Front passenger side power window auto UP/DOWN switch operated

OFF: Front passenger side power window regulator switch not operated

-

P Door P/W Up SW

Front passenger side power window manual UP switch signal / ON or OFF

ON: Front passenger side power window manual UP switch operated

OFF: Front passenger side power window regulator switch not operated

-

P Door P/W Down SW

Front passenger side power window manual DOWN switch signal / ON or OFF

ON: Front passenger side power window manual DOWN switch operated

OFF: Front passenger side power window regulator switch not operated

-

Number of Trouble Codes

Number of trouble codes / Min.: 0, Max.: 255

Number of DTCs will be displayed

-

Main Body

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

D Door Courtesy SW

Driver side door courtesy switch signal / ON or OFF

ON: Driver door open

OFF: Driver door closed

-

P Door Courtesy SW

Front passenger side door courtesy switch signal / ON or OFF

ON: Front passenger door open

OFF: Front passenger door closed

-

Door Lock SW-Lock

Driver side door lock switch signal / ON or OFF

ON: Driver side door lock switch is turned to lock

OFF: Key is in Driver side door lock key cylinder (original position)

-

Door Lock SW-Unlock

Driver side door unlock switch signal / ON or OFF

ON: Driver side door lock switch is turned to unlock

OFF: Key is in Driver side door lock key cylinder (original position)

-

Door Key P/W Up

Function to roll the driver side door window down while holding the key to the unlock side more than about 0.7 second. / ON or OFF

Customize setting displayed

-

Door Key P/W Down

Function to roll the driver side door window up while holding the key to the lock side more than about 0.7 second. / NOT ON or OFF

Customize setting displayed

-

Communication D-Door Motor

Connection status between power window regulator motor (for driver side) and main body ECU/OK or Stop

OK: Connection

Stop: No connection

-

Communication P-Door Motor

Connection status between power window regulator motor (for front passenger side) and main body ECU/OK or Stop

OK: Connection

Stop: No connection

-

Communication Master SW

Connection status between master switch and main body ECU/OK or Stop

OK: Connection

Stop: No connection

-

Communication B-Dor P/W

Connection status between back door ECU and main body ECU/OK or Stop

OK: Connection

Stop: No connection

-

Back Door P/W

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Key Switch Operation Locked

Tail gate control switch signal / ON or OFF

ON: Tail gate control switch is turned to unlock

OFF: Key is in back door lock key cylinder (original position)

 

Key Switch Operation Unlocked

Tail gate control switch signal / ON or OFF

ON: Tail gate control switch is turned to unlock

OFF: Key is in back door lock key cylinder (original position)

 

Wiper Reverse Position

Rear wiper reverse position switch signal / ON or OFF

ON: Rear wiper reverse position switch is in ON position

OFF: Rear wiper reverse position switch is in OFF position

-

Wiper Retracted Position

Rear wiper retract switch signal / ON or OFF

ON: Rear wiper retract switch is in ON position

OFF: Rear wiper retract switch is in OFF position

-

Door Key Linked Unlock SW

Function to roll the back door window down while holding the key to the unlock side more than about 0.7 second. / NOT AVL or AVAIL

Customize setting displayed

-

Door Key Linked Lock SW

Function to roll the back door window up while holding the key to the lock side more than about 0.7 second. / NOT AVL or AVAIL

Customize setting displayed

-

Back Door P/W Status

Back door glass position signal / CLOSE or OPEN

CLOSE: Back door glass is in CLOSE position

OPEN: Back door glass is in OPEN position

-

Back P/W Pos (Close-1/4 open)

Door glass position (Fully closed - 1/ 4 open) signal / OK or CAUTION

OK: Power window is going UP by manual operation

CAUTION: CAUTION may be displayed when resistance is applied in each position. In this case, there must be a foreign object stuck in that position

-

Back P/W Pos (1/4-2/4 open)

Door glass position (1/4 open - 2/4 open) signal / OK or CAUTION

OK: Power window is going UP by manual operation

CAUTION: CAUTION may be displayed when resistance is applied in each position. In this case, there must be a foreign object stuck in that position

-

Back P/W Pos (2/4-3/4 open)

Door glass position (2/4 open - 3/4 open) signal / OK or CAUTION

OK: Power window is going UP by manual operation

CAUTION: CAUTION may be displayed when resistance is applied in each position. In this case, there must be a foreign object stuck in that position

-

Back P/W Pos (3/4-Full open)

Door glass position (3/4 open - Fully open) signal / OK or CAUTION

OK: Power window is going UP by manual operation

CAUTION: CAUTION may be displayed when resistance is applied in each position. In this case, there must be a foreign object stuck in that position

-

2. PERFORM ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Warm up the engine.

(b) Turn the ignition switch off.

(c) Connect the Techstream to the DLC3.

(d) Turn the ignition switch to ON.

(e) Turn the Techstream on.

(f) Enter the following menus: Body Electrical / (desired system) / Active Test.

(g) According to the display on the Techstream, perform the Active Test.

HINT:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function does not operate.

D-Door Motor

Tester Display

Test Part

Control Range

Diagnostic Note

Power Window

Driver side power window

OFF/UP/DOWN

-

P-Door Motor

Tester Display

Test Part

Control Range

Diagnostic Note

Power Window

Front passenger side power window

OFF/UP/DOWN

-

Back Door P/W

Tester Display

Test Part

Control Range

Diagnostic Note

Back Door Power Window

Back door power window

OFF/UP/DOWN

-

Main Body

Tester Display

Test Part

Control Range

Diagnostic Note

IG OFF P/W Control Permission Output

Power window control permission output

ON or OFF

-